Tile cutting disc you can cut glass

No,cutting discs has high tensile, impact and flexural strength. Because the cutting disc  own characteristics, easy to use cut pieces chopped glass, cut glass using a glass cutter.
Glasscutter here refers to a tool used to cut glass. Section usually glass cutter for cutting glass hardness greater than diamond or alloy material.
Cut glass technique
First, use a glass cutter cut 2-3mm thick plate glass
Cutting 2 a 3m-thick plate glass available 2mm × 12mm thin wooden ruler, the first amount of glass the size of the ruler fix cut size, consider leaving neutral and 2mm 3mm incision. Cutting may have a size of one side against the side of the glass. Glasscutter close to the other end of the straightedge, grasp the blade end straight draw back, you can not have the severity of bending.
Second, with a glass cutter cut 4-6mm thick glass
4-6mm thick glass cutting method is generally the same as above, but the glass is thick, cutting to hold accurate, predict with confidence, forced the severity uniform. Another cutting method is to use 4mm × 50mm ruler, cut glass cutter against ruler. When cut, the cut in the mouth to brush up on some kerosene in advance, so that after nicking permeability easy to pull off.
Third, use a glass cutter cut 5-6mm thick chunks of glass
5-6mm thick chunks of cut glass and cutting the same method with 5mm × 40mm ruler. But the larger chunk of glass, people stand on the ground can not be cut, and sometimes need to stand on the glass cutting, you must pad flannel on the bench before cutting the glass under pressure even after cutting the glass with both hands required, while down plate off, not careless, resulting piece of glass breakage.
Fourth, glass cutter cutting wire glass
Wired glass cutting method with 5 a 6mm plate glass, wire glass cutting surface but rugged, cutting edge slippery, difficult to master, so to understand the blade, hold steady head, forced glass bigger than the average speed but also faster, so as not to appear bent not straight. After cutting the glass with both hands pull down firmly, clip wire can dial off, then use pliers to clamp the wire cut down, so as not to cut through the palm when handling.
Fifth, cut by a glass embossed glass
Embossed with a glass cutter glass cutting, embossing surface should be at the cutting wire glass with the same methods.
Six, with frosted glass cut glass cutter
With frosted glass cutter cutting, rough surface should be lower, and flat glass cutting method is also the same.

What is stainless steel special cutting disc material

Stainless steel special cutting disc is a cut sheet, as the name implies, it is designed to cut stainless steel cutting blades. This cut piece of material has a lot
1, corundum: industrial alumina powder as raw material, melting temperature above 2000 degrees to an arc formed after cooling, crushed plastic, magnetic separation to iron, screening into a variety of size, its dense texture, high hardness, grain the formation of sharp form for use in the manufacture of ceramics, resin bonded abrasives and grinding, polishing, sand blasting, precision casting (casting special corundum), etc., can also be used to manufacture advanced refractories.
2, corundum: bauxite, coke (anthracite) as the main raw material in electric arc furnace smelting at high temperature, it made use of abrasive, suitable for grinding high tensile metals, such as various Universal steel, malleable iron, hard bronze, etc., can also be manufactured advanced refractories. It has high purity, good crystalline liquidity, low coefficient of linear expansion, corrosion-resistant characteristics.
3, silicon carbide: with quartz sand, petroleum coke (or coal), wood as a raw material by high temperature resistance furnace smelting. In contemporary C, N, B and other high-tech non-oxide refractory materials, and silicon carbide is the most widely used and most economical one. It can be called emery or refractory sand, looking to adopt.

Resin-cutting storage and use precautions:

1, cutting discs handling must be handled with care to prevent the collision entire crack!
2, cutting disc should be stored moisture, antifreeze, anti-deformation, cut pieces on a wooden pallet should paperback or wooden plate, stack height does not exceed the value of the general!
3, resin-cutting storage time of one year, over the time the rotation should be re-tested to confirm compliance before using!
4, the installation angle to the cutting blades mill, require contact with the cutting disc flange surface clean and smooth, elastic moderate tightening requirements for cutting films, only allowed to use special wrench reinforcement, prohibit the use of supplementary fixtures to prevent abrasive man-made damage!
5, the cutting speed can not exceed the work piece using line speed cutting sheet under the trademark when using pneumatic grinding machine, to prevent pressure instability, resulting in cut sheet exceed the maximum speed!
6, the use of films to be slowly cutting into force, excessive force prone to stall, stuck and crashed cutting discs phenomenon, the event should be immediately cut the jammed sheet filed to avoid cutting discs burned out or broken card!
7, cutting discs only allow monolithic installation, it is strictly prohibited two or more than two simultaneous installation!
8, resin-cutting is only allowed for cutting, are not allowed for grinding!
9, cutting slices using equipment shall comply with the provisions of grinding machinery safety regulations!
10, users in the use of abrasive cutting discs are in compliance with safety rules!