Metal grinding disc

Stainless steel cutting discs  is a relatively hard material, so it's time to cut a better selection of cutting discs. Nelly times most suitable for cutting stainless steel cutting blade, and concrete cutting discs materials are corundum, corundum, zirconium corundum, crystal corundum, chromium corundum, green silicon carbide, calcined alumina, specifications from the thickness of 0.3 ~ 30mm, diameter 100 ~ 300mm not and so on, using a speed of up to 80 m / sec, complete specifications. cutting tools we upgrade, durability is another piece of cut twice, but metal cut off wheels greatly enhance the sharpness.

Cut off wheels

Flat cutting disc piece of porous concrete, concrete cutting wheels, asphalt, natural stone, basalt and basaltic products, gray cast iron. Scope: cut stones, cutting tools boards, bricks, prefabrica- Ted section, curbs, pipes and centrifugal concrete,cutting tools SML- ductile pipe, joints cutting.

Metal cutting discs

LEMAN metal cutting discs affiliated with abrasive and binder resin made for ordinary steel, metal cutting wheels metal and non-metallic materials. Made of glass fiber reinforced resin bonding material, with high tensile, impact and flexural strength, widely used for ordinary steel, Cut off wheelsl and stainless steel cutting discs production, the quality of materials, craftsmanship ensures that different materials high cutting efficiency of the workpiece and the best economic results.

flat cutting disc Abrasive Cutting - bracket

1, the bracket mounting solid and reliable; 

2, the carrier should have sufficient diamond cutting discs‍ size and strength; 

3, near the wheel side of the bracket edges should be free of dents, chipping; 

4, the position of the bracket should be able to wear with the wheel to adjust the gap, the gap should be less than or equal 3MM; 

5, bracket countertops wheel spindle centerline height ratio should be high or slightly higher than the wheel center plane 10MM; 

6, wheel diameter less than or equal time to Diamond Discs‍ the installation bays 150MM;

LEMAN metal cutting discs Precautions replacement process

Any wheel wear problems have some wear and tear of its requirements, wear a certain extent it is necessary to replace the new wheel. Not in order to save material, it requires the stainless steel cutting discs‍ use of ultra-wear, which is a very unsafe illegal behavior. A general rule, when the wheel wear to a larger diameter than the diameter of 10mm chuck should be replaced with new wheel. Valid questions from the Treasury brought out a new wheel is not necessarily qualified wheel, new wheel even buy from the manufacturers are not necessarily qualified wheel. Any wheel has its certain expiration date, within the validity period of use, it is qualified wheel; than valid use, it is not necessarily qualified wheel. Rules of order "wheel should be within the validity period, resin and rubber bonded grinding wheel rotating storage must be approved by the test, those who pass the year before use." Texture problems with the process, if you find a local wheel diamond cutting discs‍ cracks, should immediately stop using and re-replacement of the grinding wheel, grinding wheel to avoid crushing injury accident.

LEMAN metal cutting discs Precautions during use

Side of the grinding wheel machine problems in daily use, we can often find some kind of grinding machines, regardless of the operator, regardless of the type of wheel, optionally grinding bench grinder wheels‍ wheel on the use of the side, which is a serious breach of security operations Statutes illegal operation behavior. Made according to the rules with the circumferential surface of the side face of the grinding wheel should not be used, higher radial strength of this wheel, the axial strength is small, the grinding wheel can cause crushing injuries or excessive force when the operator, the actual the use of the process should prohibit such behavior. Positive operational problems in everyday use, many operators are facing the wheel always used to operate, because this direction can be put into effect, in fact, this behavior is the behavior of grinder operation should be particularly prohibited. Follow the rules, the use of grinders grind the workpiece, the operator flat cutting disc‍ should stand on the side of the wheel, the front wheel may not operate when the wheel to avoid a failure, or the wheel broken wheel flying flying wounding. Operational problems in the use of force grinder, some operators, especially the younger operators, for the sake of grinding speed, force too much too fast, this is a very unsafe behavior. Any wheel body has a certain level of intensity, this could cause the wheel broken, and even flying out of wounding, but also a should be prohibited. Common operational problems in the actual daily operations, there are also so happens, someone to catch production tasks, rob working time, the two share a grinding machine while operating, which is a serious violation of operating behavior, should be strictly prohibited. A grinding stainless steel cutting discs‍ machine is not enough time, can be used to add grinders solution, and definitely not at the same time share a grinder.

stainless steel cutting discs Abrasive cutting - cutting grinder Precautions

Wheel of use of certain hazardous. For everyone's safety, use the list below Note: Grinder is one of the most commonly used machine shop equipment, its installation is reasonable, bench grinder wheels‍ whether compliance with safety requirements; its use is correct, whether compliance with safety rules . These issues are directly related to the safety of every employee, and therefore the actual use must arouse our attention.